How do I connect a VCR to a Flat Screen TV

You may still have many video tapes that you like to play but find it hard to connect a VCR to your new flat screen TV. Often this is because you can’t find the right connections on the new TV. This article will explain the different options on how to connect a VCR to a flat screen TV, even if you can’t find the yellow socket.

Basically you need to connect from the “line out” of the VCR to “AV in” of the TV. This needs to be done for both the video and for the audio. Some VCRs have one audio out socket (mono) and some have two audio out sockets (stereo) – we will look at stereo first, and look at the differences for mono later in this article.

Connect a VCR with the Yellow, Red and White Leads

Connect a VCR with RCA leads

To connect a VCR to most flat screen TVs, you will need a cable with these yellow, red and white connectors. For non European VCRs, you will need a cable with these plugs at each end. For European VCRs, you may need a SCART plug at one end, and these yellow, red and white plugs at the other end to connect to the TV.

These plugs are often called RCA or Phono plugs. The yellow cable is used for the video signal, the red cable for the right audio, and the white cable for the left audio signal. Many VCRs come with these leads supplied. If you don’t have any, they should be available at most electronic or electrical stores.

The rear of the VCR

Connect a VCR Stereo out

This photo shows the standard connectors on most (stereo) VCRs. If you look closely, on the right hand side are the “line out” sockets (the left hand side is for “line in”, which we don’t use for connecting to a TV). The top right red socket is for the right audio out. The white middle right connector is the left audio out socket. The yellow socket at the bottom right is the video out socket.

The markings or labels on most VCRs are as hard to read as in this photo, so you may need to use a torch to see the markings clearly. Once you have found the line out sockets, it is a simple matter of connecting the yellow, red and white plugs of the connecting cable to the corresponding yellow, red and white line out sockets of the VCR.

The Rear of an Older Flat Screen TV

Connect a VCR LCD connectors

Older flat screen TVs are easy to connect a VCR to as they have at least one yellow “video in” socket. In this photo you can see it just below the centre of the photo, it is labelled “Video”. Below this yellow socket for video in is the corresponding white and red sockets for the left and right audio in.

Having found the yellow, red and white sockets, it is a simple matter of connecting the corresponding yellow, white and red plugs of the cable connected to the VCR to these sockets.

You may have noticed that in this photo, these sockets are in a section labelled “VIDEO 1 IN”. This normally would indicate that this is the input you need to select on the TV to watch the VCR. Most TVs require you to press “Source” or “Input” on the remote control to select the “Video 1” input signal.

Other TVs might label these inputs “AV” (short for Audio/Video).

Some older TVs might have several AV inputs, normally labelled AV 1, AV 2 etc. Many older flat screen TVs also have AV inputs on the side of the TV as well as on the rear of the TV.

My TV doesn’t have a Yellow Socket!

I get many questions from people saying they can’t find the yellow socket to connect a VCR into. Don’t worry, I have a solution. But first check the sides of your TV to make sure the designers aren’t trying to trick you by hiding the yellow, red and white sockets up one side.

Don’t worry if you can’t find a yellow socket to connect a VCR in to, as many new TVs don’t have one. Manufacturers think there is no need to supply TVs with the ability to connect a VCR through the standard (and old) yellow, red and white sockets. Instead some TV’s let you connect to the green socket, and others require you to use a HDMI input. I discuss each way below.

If there is a Green Socket

connect a VCR to new TVAt the rear of many flat screen TVs there is no yellow socket for “Video In”. But as you can see in this picture, they say you can use the green socket instead. Notice on this TV, (and most others) there is only one of the green sockets nominated as “Video in” for you to connect a VCR to.

So for this TV, you would connect the yellow lead from the VCR to the nominated green “Video in” socket. The red and white audio leads from the VCR would connect to the corresponding red and white audio sockets below the blue and red.

Be careful not to fall into the trap of connecting the red audio cable, to the other red socket labelled “Pr” – the right audio will not work if you do this. Also ensure you don’t connect anything to the blue or red video inputs or your VCR picture will be in black and white only.

Note that not all TVs label the “video in” as clearly as in the photo above. Some simply put a yellow circle around the appropriate green socket. Some use a combination of yellow and green. Others label this socket as “Composite Video”.

conenct a VCR with Composite Video

Composite Vs Component Video

You don’t need to understand this section – it is for those people who like to understand why it is possible to connect a VCR this way.

The green, blue and red sockets labelled Y, Pb and Pr in the photo above are for connecting a DVD player. These three video signals are called “Component Video”. It is the best way of connecting a DVD player if the DVD player doesn’t have HDMI. The green input from a DVD player is basically the black and white picture. The blue and red inputs are for the colour information of the picture. Then the other red and white sockets are for the right and left audio.

The video signal from a VCR has the black and white picture and the colour information all joined together – called composite video.

Modern TVs are clever enough to know when you only have one lead connected with all the information (composite video) or separate leads (component Video).  Hence they don’t need to provide a separate input for Composite only. For a more detailed explanation of component video see this article, or this article to learn more about composite video.

Connect a VCR with HDMI only on the TV

Many new TVs do not have any analogue inputs. Therefore you need to use one of the HDMI inputs on the TV.  However you can’t connect your VCR directly to the TV, you need a converter box. Something like these offerings from Amazon:

This allows the yellow, red and white lead from the VCR to be plugged into the input of the converter box. The output of the converter box connects to a HDMI lead. The other end of this lead will plug into one of the HDMI inputs of the TV.

If you are going to buy a composite(RCA) to HDMI converter consider these tips:

  • Beware, many on-line searches return two types of converters: a RCA to HDMI converter and the reverse, a HDMI to RCA converter. To connect a VCR to a TV using HDMI, you need a RCA to HDMI converter.
  • You may also need to buy a short HDMI lead, if you don’t already have a spare one.

My VCR only has a white audio out

Many VCRs are not stereo, they are only mono. TConnect a VCR mono audiohat is, they do not output a left and right audio channel. Instead they only output one single audio channel (mono audio). Therefore, they do not have a red and white audio output (for right and left audio). They only have a white output, for the mono audio. You may remember most old TVs only had one speaker, so the VCR only needed one audio channel (mono).

To connect a VCR with only mono audio to a flat screen TV, simply go from the “audio out” socket of the VCR.

That is the easy bit. How you connect to the TV will depend on the TV.

Connect a VCR - monoSome TVs will have sockets on the back like this picture. On the left hand side you should see the Audio right (red) and left (white) input sockets. The left socket is also labelled “MONO”. If your TV is like this, then simply connect the “mono out” from the VCR to the “mono in” of the TV. The TV should direct the sound to both (left and right) speakers of the TV.

If your TV does not have a Mono input, then you have two or three options:

  1. You can simply connect the “mono out” from the VCR to the “Left in” on the TV. This will send the sound to the left speaker only. While you might think this is not ideal, you may be surprised that it sounds fine when sitting some distance from the TV. The red cable is not used if connecting to the TV this way – it can just hang on its own behind the VCR and TV.
  2. You Connect a VCR Mono adapter leadcan use a cheap mono to stereo adapter cable. The single (black) plug is connected to the white audio out of the VCR. Then a normal red and white audio lead is connected from the adapter cable to the right (red) and left (white) audio in sockets of the TV. This will send the same mono audio to both the right and speakers of the TV.
  3. You can also use a mono to stereo adapter plug. This plugs straight into the ‘Audio Out”Connect a VCR RCA splitter on the back of the VCR. Then a normal red and white audio lead is connected from the two sockets of the adapter to the right (red) and left (white) “audio in” sockets of the TV. This works exactly the same as the lead above – use whichever one is available to you.

Whichever way you connect the mono audio, you will hear the sound through the TV. Keep in mind that many video recordings were probably recorded in mono, so you are not missing much.

Don’download articlet forget to also connect the yellow video lead from the VCR to the TV (as described above).

If you still have a problem to connect a VCR to your TV, list the details of the equipment and your problems in the comments box below, and together we can all learn other issues involved.


  1. I have a Toshiba tv (model 40E220U) and a Sears VCR (model 30437). It is a mono output. I’ve managed to get it to work but there’s no colour. I’ve got the yellow lead in the green video in outlet and the white in the white L/Mono outlet. What am I doing wrong?

    • Hi Kristal,

      It looks like you have it connected correctly. However on your TV there is also a setting change you need to make in the menu. Go to preferences and then select AV input. You need to select video and not ColorStream HD.

      Let me know if this works and not.



  2. I have a Toshiba SD V-390 DVD/VCR connected to a Samsung UN32J4000CF LED tv as per your instructions above. I get menu setup, etc from the VCR, but recording only gives me fuzz.

    • Hi Carol,

      You have done well. You have connected the TV to the VCR, so it plays videos on the TV. That is the purpose of this article, as most people simply want to play their existing video tapes.

      VCRs were designed to record analogue TV programs. Most programs these days are digital, and look very poor when recorded on a VCR. PVRs (personal video recorders) will record digital programs and keep the quality good.

      If you want to record the Free-to-air TV programs on a VCR, you will probably need a digital set top box, which receives the digital TV signal and gives an analogue output (through the yellow, red and white connections) which can then be recorded on the VCR. You can also record from a cable box if the cable box also has the yellow, red and white leads.

      Does this help?


  3. I have a new Sony XBR-49X900E TV and want to hook up a VCR to it so I can play tapes containing content not available on DVD. The TV has the RGB ports on the back but not a coax port except for the antenna port (which I have an antenna plugged into since I don’t have cable). I have a combo Sony DVD/VCR SLV-D300P and a standalone Sony VCR SLV-N900. First I tried the combo using the RGB ports and got “no input detected”. Then I tried the standalone VCR SLV-N900 and get the same thing, “no input detected”. I also have a Sony DVD DVR-SR210P. When I plug that into the same RGB cables going into the same ports in the TV, that works great. I read somewhere that new TVs may not be able to see the low resolution of a VCR. Is that what’s going on here? If so, how do I fix that? I don’t have a coax port to plug the VCR into the TV. Would it work if I get a RGB to HDMI converter, even though I have RGB ports on the TV and it doesn’t work in those?

    • Hi Margaret,

      I think the RGB bit is the problem. Mainly because a VCR does not have a RGB output – only the DVD does.

      So use the yellow, red and white sockets on the other side of the rear of the VCR. Then connect the yellow lead from the VCR to the green socket labeled video on the back of the TV. Don’t plug anything into the adjacent blue and red sockets. Then the red and white from the VCR plug in to the red and white audio in on the TV.

      No play a video. On the TV, select video 2.

      Does that work?


  4. Hello there, I am an elderly lady (70’s) and not really computer literate so I hope you can assist me in layman’s (laywoman’s) terms! My VCR has only yellow and white sockets and the leads I have, have yellow, white and red plugs on the ends. The back of the TV has (on the left) red and white outlets with the words AV In Component written above them and the word Audio below. To the right of this are red, blue and green sockets and below are the words /Video and Video. I connected the yellow and white leads into the back of the VCR and the white lead into the white outlet at the back of the TV, but where do I connect the yellow lead to in the back of the TV if there is no yellow connection in the TV? I hope that isn’t too convoluted an explanation? Regards, Anne.

    • Hi Anne,
      You are almost there – well done.

      Connect the yellow lead from the VCR to the green socket on the TV.

      It should now work.


      • Hi again, I keep getting a no signal message on my TV when I press av to record a program from the TV. should the antenna be in the VCR or the TV? the VCR is a Philips g code NTSE playback turbo drive vr255 VHSHQ video cassette recorder, regards, Anne

        • Hi Anne,

          The problem is the VCR does not record what the TV is showing. Instead, the TV shows what the VCR is recording.

          The problem is, the VCR was made for analogue TV. Now all your channels are digital, the VCR can not record them, as it only has an analogue tuner.

          You can still play any videos you have previously recorded, but the VCR wont record the programs directly.

          However there is still a way. You will need to purchase a digital set top box (STB). They are available from places like Harvey for under $50. If you want to do this, let me know and I’ll explain how to connect it all up.


  5. Geoff,
    I have a Proscan TV model PLDED5520-UHD, a Magnavox DVD/VCR combo model MWD2205 and a Panasonic Stereo system model SA-AK58. I would like to connect all three in such a way as all audio would come out the stereo system speakers. If possible, how would I do this?
    Thanks for your time and consideration!

    • Hi Julie,

      I can’t find a manual for your TV, but I did find one for a similar model, so hopefully they are similar.

      My basic concept is to use the CD player/amp to listen to everything that goes through the TV. So basically you need to connect the TV to the amp. You will need a 1/8″ plug to 2 RCA plugs to do this. Plug one end into the headphone out of the TV, and the other end to the Aux in of the amp. Now select AUX on the Amp and the sound from the TV should come through the speakers.

      Now connect the VCR/DVD to the TV using the yellow, red and white sockets. Now when you play a VCR or DVD through the TV, the sound will come through the amp speakers.

      Hope this helps


      • You rock Geoff!!!! Thank you so very, very much. It’s just what I needed. I’m gonna tell my friends about you.

  6. Hi,

    My VCR/TV is suddenly not showing an image. There is sound when a VHS is being played. I am not sure which cable is for showing a picture, but all looked fine when I checked. Does a cable need replacing and if so, which one?


    Candice 🙂

    • Hi Candice,

      If it is a cable issue, it will be the yellow cable. However it is not common for a cable to go faulty without it being touched.

      The other common cause is dirty heads. Try cleaning the heads and then try a different tape. Don’t use the current tape again as it could be causing the dirty heads.


  7. Hello Geoff,

    Thank you so much for your helpful advice. In the end I used the straightforward SCART-SCART connection with success.

    Kind regards,

  8. Hello Geoff
    I have the following – Sony VCR SLV-SE800G
    Sony Bravia TV
    Panasonic Disc Player/HDD Recorder DMR-PWT550
    I am trying to set up my old VCR to work on the TV. Your article is brilliant but I need a little more advice please. Both VCR and TV have a SCART connector. The TV also has a spare HDMI port and a green connector. The VCR has yellow/red/white connectors for video etc. Do I use a RCA – HDMI converter plus a short length of HDMI cable or do I use the SCART connectors or both?

    • Hi Sylvia,

      It appears there are several way you could try connecting the VCR to the TV.

      You should be able to use the SCART cable. Use the bottom SCART connector on the VCR (labelled line 1-TV). Then select the appropriate input on the TV.

      Alternatively, you should be able use the yellow/red/white lead from the VCR, and connect it the green, white and red socket on the TV, making sure nothing is connected to the blue and other red input. This will only work if the yellow/red/white is an output and not an input.

      Try these first. If these don’t work, then you may need a HDMI converter, but it also use these outputs so you shouldn’t need to do this.

      let me know how this goes.


    • Hi Dino,

      You will use the green/yellow socket for the video (yellow on the VCR) and the red and white audio sockets for the audio from your VCR. Don’t use the middle red and blue.


  9. Thank you for explaining that you can connect the yellow composite cable into the green component cable. I had no idea we could do that. Happy I can now watch my old movies that I can only find on VHS.

  10. Hi Geoff,
    I used the RF-G1208 component video cable(red, blue and green) to connect my Samsung TV HDTV with only red & white audio and red, blue and green component in connectors to my Sanyo VHS recorder that has only yellow, white and red connectors. The sound works but the picture is in black and white. Do I need different cable connector or an adapter?

    • Hi Katie,

      From your description it sounds like you have the blue and red component cables still plugged into the TV. You will only get a black and white picture like this. Disconnect them completely from the TV and see if that works (just leave the green one connected). The other end of the green lead should plugin to the yellow socket of the VCR (as you have it).


  11. Hi Geoff, Just hooked up a LG flat screen TV, but when I turn the VCR on loses picture and has static for about 2-3 seconds, then picture is back on and everything works normal. The flat screen I replaced, this didn’t happen. Any Ideas?

    • Hi Gary,
      It appears like it could be the tape is taking time to sync to the correct speed. Make sure you have auto tracking turned on if that is a feature of your VCR.

      I can’t explain why it is just happening with the new TV and not on the older one. It would be interesting to hook it back up to the old one to check it is not happening there too.


  12. I have a VCR/DVD Combination player that has Component Video outlets which match inputs on my TV. I have connected the two units. The DVD section on my Combo player plays O.K. However the VCR section of the player will not. Can you help, Am I doing something wrong?

    • Hi Lawrence,

      The DVD output is via the component sockets (as you have it). However the VCR signal is only outputted via the composite sockets (yellow, red and white). Fortunately, the composite outputs the DVD along with the VCR signal. If you only have one set of Analogue inputs, (which most TV have) then you will need to connect to the TV with just the yellow, red and white.

      As explained above, connect the yellow lead from the VCR/DVD to the green input of the TV. Leave the adjacent blue and red sockets empty on the TV. Connect the red and white audio to same sockets on the TV as you had them for DVD.

      Hopefully that will make it all work for you.


  13. hi.. I have a problem with my cable box with Rca cable and my new Philips TV does not have Rca connection.. only hmdi and the green blue red white connection.. when I put the yellow to green on my TV.. my video is black and white.. no color at all.. can u help me plsss

    • Hi Chatz,

      It seems the TV thinks you are feeding a Component signal into the green, red and blue socket rather than just a composite signal in the green only.

      There are two common causes of this:
      1. Some TVs need you to select “AV in” or “Composite” as the input. Most TVs do this automatically, but without knowing the model of your TV I don’t know if this it the case for you.
      2. When you use the green input for composite as you have done, (and this is the right thing to do), you can not have anything plugged into the adjacent blue and red socket. If you do, the TV thinks you are sending the color information via those sockets.

      Does this help?


      • no changes.. black and white.. my TV is Philips 6800. . and I can’t find in settings the av in.. I put the yellow on green and red and white for the audio.. no problem on audio.. only the color of my TV

        • Hi Chatz,

          Looking at the manual for your TV, it appears they have not included the function of being able to display composite Video by connecting it to the green component input – at least they don’t mention it as a possibility in the manual or the Specs.This is the first TV I’ve seen this.

          All is not lost. You can purchase a composite to HDMI converter for around $15. Just make sure it is Composite to HDMI and not a HDMI to composite converter. This will have the yellow, red and white socket, and a HDMI output, which will connect directly to the TV.


  14. Geoff,

    I have a Samsung series 56 smart tv connected to a vintage panasonic dvd/vcr PV D4742 /52. Before I upgraded our Dish receiver from SD to HD (Hopper) we were able to view tapes and dvds with sound and picture through the tv. After the upgrade, the composite/component three wire RCA setup is connected, but in component mode, the vcr produces sound/no video, and the dvd player produces video and sound, but sound only through my stereo system amp and external speakers. Should I try the converter box to cure the problem?

    Bob G

    • Hi Robert,

      From your description, it seems you have connected your VCR/DVD player to the TV via the component connections (green, red and blue) on the DVD and the TV.

      There are two problems with this. The main one being that only the DVD side of the DVD/VCR gives an output on the component sockets. You will never get the VCR to work with the component outputs. To get both to work on the one set of cables, you need to use the AV out (Yellow, red, white). This output has both the VCR and DVD.

      So normally the yellow lead from the VCR/DVD will go to the green input on the TV. You must leave the red and blue sockets on the TV empty. The red and white audio will go the red and white audio input sockets on the TV.

      If this doesn’t make sense, or doesn’t work, please spend me some pictures of your connections and I’ll try to work it out for you.


      • Worked as you diagrammed! As a bonus I used the audio out 2 to push sound through my stereo system and everything works as before. I guess the Dish installer didn’t know as much as he thought. Can’t thank you enough.
        One additional question: what causes the slight delay (echo) in the sound coming from the tv and stereo speakers when both systems are on?
        Again, many thanks.

        Bob Green

        • Hi Bob,

          I’m pleased you got it going – well done. The DVD picture would be better via the component inputs, but most TVs these days only allow one analogue input (if that), so to use the combined VCR/DVD output you need to use the composite (yellow), as you have done.

          The time delay likely to be in the TV. It can take a few milli-seconds for the TV to process to picture, so it delays the audio by the same mount to keep them in sync. For this reason I usually suggest you connect your sound system directly to the TV audio output, then it should be in sync, and you can listen to the better sound for any TV program, not just DVDs.


  15. I need to connect an old sharp vcr to my new samsung flat screen. I was told since I don’t have the hdmi port on the vcr I can’t. Isn’t there some kind of adapter I can purchase that will make it work? Thank you for your assistance.

    • Hi Martha,

      You are correct in that will need an adapter if your TV does not have any of the colored analgue inputs mentioned above. It seems like there a a number of TVs which only HDMI inputs now.

      In this case you will need a Composite (RCA) to HDMI converter, like one of these. Just make sure you get a RCA to HDMI and not a HDMI to RCA.

      hope this helps


  16. We have an old VCR that we have been using to record TV and play pre-recorded tapes with our Samsung HD Smart TV and Sky box with no problems. We now have a MySky HDi box and the technician did not connect the VCR through the MySky box so we obviously can’t record off the TV any more, not really a problem as the MySky box will do that.

    BUT, despite the VCR still being connected to the TV exactly the same as it was (a coaxial cable from the out socket on the VCR to the in socket on the TV), the TV now does not recognise the VCR player in its “source” list and we can no longer view anything playing on the VCR. Why is this? The only change is that the TV is now connected to the MySky box and the VCR separately!
    Thank you.

    • Hi David,

      I want to make sure I have the same understanding of the terms you use. When you say the VCR is connected to the TV via a coaxial cable, I assume you mean it is just one cable going from the VCR to the TV antenna input. If this is case, then it wont turn up as a source on the TV. It will be a channel on the ATV (analogue TV).

      If however you mean the yellow, red and white leads, then I need to know what that is connected to on the TV. A picture of the connection on the TV and/or the model of the TV would be useful. Also what connection is between the MySky box and the TV? I assume it is a HDMI lead.



      • Hi Geoff,

        Thanks very much. Yes, the coaxial is just the one cable (like an aerial cable) going from the VCR to the TV. The Sky box is connected to the TV by an HDMI lead.

        Looking at the other questions and answers, I obviously need to get a set of component leads. The VCR only has mono output, but that is covered in another question, so I’ll get the leads tomorrow and see how I go 🙂

        Many thanks, david

  17. Hi Geoff,

    I just bought a vcr but the vcr doesn’t have a spot for the red cable and therefore I don’t know where to plug it in. Where can I plug it in?

    • Hi Daniela,

      It sounds like the VCR is mono only, not stereo.

      This means you can forget about the red lead, or use one of the suggestions in the article above under the heading “My VCR only has a white audio out”.

      If your VCR is different to this, can you take a photo of the connections at the back and email it to me?

      hope this helps


  18. Hi Geoff-
    My Samsung tv only has HDMI ports, and I’m trying to connect a VCR and a DVD player to the tv. I have tried an RCA to HDMI cable wo success. Is there a converter box/cable you’d recommend in my case? Here’s what I’ve got:
    Samsung TV: UN55KS800 (only HDMI inputs)
    Sony DVD player: DVP-NS415 (R/Y/W, R/G/Blu, coax out)
    Panasonic VCR: PV-9660 (R/Y/W, coax out)

    Thanks in advance!

    • Hi Rich,

      I don’t understand how a RCA to HDMI cable can work as they are two completely different types of signals, so need some smart electronics to convert one to the another.

      Having said that, there are many such converter boxes, and they are now not too expensive. You could start by looking at these. Although they all look the same, just different brands. For the price of them, you could possibly get two, and use one for the VCR and one for the DVD player.

      How times change so quickly, I remember seeing my first TV that had one HDMI input and many other sockets – not that long ago. Yours is the first I’ve seen with no Analogue inputs. I imagine this is going to be trend now, especially with 4 K TV.

      hope this helps


      • Hi Geoff,
        Thanks for the guidance. I just saw your post this evening and ordered one of the converter boxes. Hope to share a success story with you in a day or two.
        Yes, the world is changing quickly!

        All the best,

  19. Hi Geoff,
    I have to decide whether to get my old 30-inch tube Toshiba repaired (love that TV) for a pincushioning problem or spring for a new LED. I do know of a repairman who will come to the house at a reasonable cost. At issue is hooking up an old VCR, DVD player and Xbox. While I’m sure I can rig up something for the DVD, I want to be able to record on the VCR as well. I do have converter boxes because I’m using them now with an antenna. Will that work?

    • Hi Ilene,

      Basically if your older TV works with your current set up, a new TV also should. You may have to get a video switch, but they don’t cost much.

      A VCR doesn’t record off a TV, rather, a TV displays what the VCR is recording. That is why you need a “Converter Box” to allow the VCR to record in your current setup.

      hope this helps some,



Please enter your comment!
Please enter your name here

Time limit is exhausted. Please reload CAPTCHA.

This site uses Akismet to reduce spam. Learn how your comment data is processed.