HomeUnderstanding AudioUnderstanding Audio Frequency

Understanding Audio Frequency

Every sound we hear is at a certain frequency. When we say someone has a deep voice, we are describing a voice producing low frequencies. Similarly if we say someone has a high pitched voice, we are describing a voice producing higher frequencies. So, what is frequency?

What is Frequency?

Technically, frequency is the number of waveforms generated in one second. As an example, if you hit the middle C key on a piano, the strings in the piano will vibrate back and forward around 261 times per second. This produces a sound wave which repeats itself 261 times each second. Therefore the frequency of middle C is 261 cycles (of the sound wave) per second.

Hertz is used as the unit of measurement for frequency in honour of the German physicist Heinrich Hertz for his work on radio waves

Rather than using “sound waves per second” or “cycles per second”, the word Hertz was adopted as the international SI unit for frequency in 1930. Hz is used as the shortened form of hertz. One hertz is the same as one wave form or one cycle per second.

Being a metric unit, the prefix kilo (k) is used for larger numbers. Example 1: A frequency of 1000Hz can also be called 1kHz, often simply called 1k. Example 2: 10k is short for 10kHz or 10,000Hz.

Music and Frequency

We saw earlier that the musical note middle C has a frequency of  261Hz (261.626Hz to be more precise). On a 88 key piano the lowest A note is 27.5Hz. The highest A note is 3520Hz. The following table gives the frequency of each A note for each octave on the piano, starting with the lowest.

A0A1A2A3A4A5A6A7
27.5HZ55Hz110Hz220Hz440Hz880Hz1760Hz3520Hz

There are a couple of interesting points to see from this table. Firstly, the frequency of any note doubles as you go up one octave. Consequently, the frequency of any note halves when you go down one octave. Secondly, most of the notes of a piano have a frequency below 1000Hz.

It is also interesting to note that the piano has a very wide range of frequencies compared to most other instruments. See the table below for a few examples (frequencies rounded to the nearest whole hertz).

InstrumentLowest FrequencyHighest Frequency
Double Bass41Hz247Hz
Cello65Hz988Hz
Guitar82Hz880Hz
Clarinet165Hz1567Hz
Violin196Hz3136Hz
Flute262Hz3,349Hz

The human voice also has a limited frequency range. The following table gives the approximate range of frequencies for different types of singers.

Singer TypeLowest FrequencyHighest Frequency
Bass82Hz330Hz
Baritone87Hz350Hz
Tenor130Hz525Hz
Contralto175Hz700Hz
Soprano260Hz1,050Hz

Harmonics

While all the above is interesting, instruments and voices don’t just produce one fundamental frequency for each note as listed above. They also produce what is known as harmonics. Harmonics are multiples of the fundamental frequency. For example, if you produced a sound at 1000Hz, there would also be sounds at 2000Hz, 3000Hz, 4000Hz and so on at various levels. The following table may help:

NameFrequencyFormula
Fundamental Frequency1000HzFundamental Frequency x 1
1st Harmonic2000HzFundamental Frequency x 2
2nd Harmonic3000HzFundamental Frequency x 3
3rd Harmonic4000HzFundamental Frequency x 4
etcetcetc

The point being, any microphone, amplifier and speaker system needs to be able to reproduce more than just the basic fundamental frequencies. Also the harmonic frequencies need to be considered when adjusting the tone of any instrument or voice. More on this in a later article.

Our Frequency Range

It is generally accepted that the hearing range of humans is 20Hz to 20,000Hz (20kHz). While we lose the ability to hear higher frequencies as we age, 20Hz to 20kHz is generally considered to be the human hearing range. It would also be good if the frequency range of any sound system was also 20Hz to 20kHz. However, very few sound systems are capable of this full range – especially at the bottom end (the lower frequencies). Nor do all sound systems necessarily need to be capable of 20 to 20kHz – it all depends on the intended use (and budget).

It is useful to know how to read a frequency chart which shows the frequency response of a speaker or microphone. The following is an example of a frequency chart for a speaker.

The first thing to notice is the scale at the bottom. On this chart it starts at 50Hz and displays numbers for 100Hz, 500Hz, 1kHz, 5kHz, 10kHz, 20kHz and 40kHz. Notice how it is not linear, but rather it is spread out over the lower frequencies and bunched up more over the higher frequencies. This logarithmic scale also closely matches the spread of frequencies we saw when looking at the piano frequency range.

The blue line is indicating the frequency response of the speaker under test. This speaker has a fairly flat response across the entire audible frequency range, with a drop off at the bottom end around 70Hz.  You may see graphs like this for speakers and microphones. They are useful to alert us to any major troughs or peaks in the frequency response which will need to be dealt with for good sound – mind you, if there are major peaks or troughs, you will probably hear that it doesn’t sound right.

This introduction on audio frequency gives a basic understanding of the principles involved. This topic will be expanded when looking at equalization and system setup.

Further reading

Please Note: Due to other commitments I'm currently unable to spare the time required to answer further questions in the way I'd like. Hopefully this is a temporary situation. I'm sorry for this inconvenience.
Geoff

2 COMMENTS

2 Comments
Inline Feedbacks
View all comments

Popular this week

Connecting with...

350FansLike
13,500SubscribersSubscribe